| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
C |
A |
1215 |
L |
CH |
- |
F0 |
|
|
|
|
|
| |
1 |
2 |
|
3 |
4 |
|
5 |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
1. |
S = Steel |
|
|
|
|
|
|
|
|
|
| |
C = Carbide |
|
|
|
|
|
|
|
|
|
| |
H = Heavy metal |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
2. |
A series uses CDCD or CDCC type inserts |
|
|
|
|
| |
B series uses TDAB or TDAC type inserts |
|
|
|
|
| |
C series uses TPGB2, TPGC2 or TPGH2 type inserts |
|
|
| |
D series uses TPGB3, TPGC3 or TPGH2 type inserts |
|
|
| |
E series uses WCGT0 |
|
|
|
|
|
|
|
| |
F series uses WCGT1 |
|
|
|
|
|
|
|
| |
G series uses WCGT2 |
|
|
|
|
|
|
|
| |
H series uses WCGT3 |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
3. |
Add L to part number for left hand bar |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
4. |
Add CH to part number for coolant hole. Coolant hole |
|
|
| |
is available in all carbide and steel bars beginning at 3/8"; |
|
| |
heavy metal bars available with coolant hole as Special Only. |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
5. |
Straight shank boring bars in Series A through D may be |
|
|
| |
used in collet holders and do not have flats. Flats may be |
|
| |
ordered using the following identification: |
|
|
|
| |
F0 |
parallel to the insert, same side as the insert |
|
|
|
| |
F90 |
perpendicular to the insert, same side as the insert |
|
|
| |
F180 |
parallel to the insert, reverse side from the insert |
|
|
| |
F270 |
perpendicular to the insert, reverse side from the insert |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
multiple flats may be ordered by combining identifications |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
Be sure to use a LEFT hand ground chipbreaker insert with RIGHT hand
boring bars |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
Be sure to use a RIGHT hand ground chipbreaker insert with LEFT hand
boring bars |
